From: Steve on 15 Apr 2006 13:58 Has anyone any old install notes for an Emmegas changeover/controller box ? Could do with some wiring notes please ! Steve
From: SWB on 4 May 2006 12:20 Steve Wrote: > Has anyone any old install notes for an Emmegas changeover/controller > box ? > > Could do with some wiring notes please ! > > Steve I've got the same problem.. its an EmmeGas controller box and has a 7 pin plug on the back. The wires are coloured: 1 - Green - gas level sensor? 2 - Not used. 3 - Purple - ?? 4 - Blue - ?? 5 - Red - +12V 6 - Yellow/Green - Gnd. 7 - Brown - ?? Came from ebay with out instructions! Much appreciated, Toby -- SWB
From: Steve Taylor on 6 May 2006 17:29 SWB wrote: > Steve Wrote: >> Has anyone any old install notes for an Emmegas changeover/controller >> box ? >> >> Could do with some wiring notes please ! >> >> Steve > > I've got the same problem.. its an EmmeGas controller box and has a 7 > pin plug on the back. The wires are coloured: > > 1 - Green - gas level sensor? > 2 - Not used. > 3 - Purple - ?? > 4 - Blue - ?? > 5 - Red - +12V > 6 - Yellow/Green - Gnd. > 7 - Brown - ?? > > Came from ebay with out instructions! > Much appreciated, Toby > > > > 7 Brown. Sparks pickup. Wrap at least 5 turns round the wire from the coil. Steve
From: Austin Shackles on 7 May 2006 08:20 On or around Sat, 06 May 2006 22:29:38 +0100, Steve Taylor <Steve(a)ravenfield.com> enlightened us thusly: >SWB wrote: >> Steve Wrote: >>> Has anyone any old install notes for an Emmegas changeover/controller >>> box ? >>> >>> Could do with some wiring notes please ! >>> >>> Steve >> >> I've got the same problem.. its an EmmeGas controller box and has a 7 >> pin plug on the back. The wires are coloured: >> >> 1 - Green - gas level sensor? >> 2 - Not used. >> 3 - Purple - ?? >> 4 - Blue - ?? >> 5 - Red - +12V >> 6 - Yellow/Green - Gnd. >> 7 - Brown - ?? >> >> Came from ebay with out instructions! >> Much appreciated, Toby >> >> >> >> > >7 Brown. Sparks pickup. Wrap at least 5 turns round the wire from the coil. HT wire, that is... -- Austin Shackles. www.ddol-las.net my opinions are just that "Carpe diem, quam minimum credula postero" (sieze today, and put as little trust as you can in tomorrow) Horace (65 - 8 BC) Odes, I.xi.8
From: SWB on 7 May 2006 05:38 Steve Taylor Wrote: > SWB wrote:- > Steve Wrote: - > Has anyone any old install notes for an Emmegas changeover/controller > box ? > > Could do with some wiring notes please ! > > Steve- > > I've got the same problem.. its an EmmeGas controller box and has a 7 > pin plug on the back. The wires are coloured: > > 1 - Green - gas level sensor? > 2 - Not used. > 3 - Purple - ?? > 4 - Blue - ?? > 5 - Red - +12V > 6 - Yellow/Green - Gnd. > 7 - Brown - ?? > > Came from ebay with out instructions! > Much appreciated, Toby > > > > - > > 7 Brown. Sparks pickup. Wrap at least 5 turns round the wire from the > coil. > > Steve Thanks for the reply. That confirms what I've worked out from other controller boxes. Green - LPG level sensor Purple - Petrol cut off solenoid Blue - LPG solenoid Red - +12V Yellow/Green - Gnd. Brown - coil neg. terminal or rev counter pickup etc Hope this is of some help to anybody else. -- SWB
|
Pages: 1 Prev: Looking for cheap sources of LPG Next: Who can certify a system? |