Prev: Suggestions from your experience organizing metric & english combination box/open end wrench sets?
Next: Suggestions from your experience organizing metric & englishc...
From: The Daring Dufas on 5 Jul 2010 02:42 On 7/4/2010 11:27 PM, Bill Horn wrote: > Sometimes a good idea is only a suggestion away. > > I have your typical set of metric and english combination box/open-end > wrench sets in various drawers in my toolbox. > > But they're all jumbled about such that it takes longer than I'd like to > grab a certain size or a sequence of certain sizes. > > How do you store your combination wrenches so that they are easy to access? A little spray paint to denote metric or standard? I've seen socket sets and wrench sets that came from the factory with different colors to denote English or metric. TDD
From: willshak on 5 Jul 2010 11:00 Bill Horn wrote the following: > Sometimes a good idea is only a suggestion away. > > I have your typical set of metric and english combination box/open-end > wrench sets in various drawers in my toolbox. > > But they're all jumbled about such that it takes longer than I'd like to > grab a certain size or a sequence of certain sizes. > > How do you store your combination wrenches so that they are easy to access? > Separate drawers for SAE and Metric. Lined drawers with wrenches laid out from small to large. Of course, that is only when I have nothing to do and just sort them all out. Usually, they are all jumbled up. Sometimes, it helps if we are a little OCD. -- Bill In Hamptonburgh, NY In the original Orange County. Est. 1683 To email, remove the double zeroes after @
From: LSMFT on 5 Jul 2010 11:20 On 07/05/2010 12:27 AM, Bill Horn wrote: > Sometimes a good idea is only a suggestion away. > > I have your typical set of metric and english combination box/open-end > wrench sets in various drawers in my toolbox. > > But they're all jumbled about such that it takes longer than I'd like to > grab a certain size or a sequence of certain sizes. > > How do you store your combination wrenches so that they are easy to access? First I keep the metrics separate from the SAE including sockets and hex keys. In my case, a separate drawer. Next I stack 2 together with the largest in the rear and smallest in the front. Lastly, don't slam the drawer. Eventually a tool box needs to be tidied up once in a while. A rubber mat in the bottom of the tool drawer helps to keep them from sliding around. I found that the rubber mats for kitchen cabinets with the holes in it to work good in a tool box. You can even glue them in. If you hang your tools then it's a no brainer. -- LSmFT I'm trying to think but nothing happens............
From: LSMFT on 5 Jul 2010 11:18 On 07/05/2010 12:27 AM, Bill Horn wrote: > Sometimes a good idea is only a suggestion away. > > I have your typical set of metric and english combination box/open-end > wrench sets in various drawers in my toolbox. > > But they're all jumbled about such that it takes longer than I'd like to > grab a certain size or a sequence of certain sizes. > > How do you store your combination wrenches so that they are easy to access? First I keep the metrics separate from the SAE including sockets and hex keys. In my case, a separate drawer. Next I stack 2 together with the largest in the rear and smallest in the front. Lastly, don't slam the drawer. Eventually a tool box needs to be tidied up once in a while. A rubber mat in the bottom of the tool drawer helps to keep them from sliding around. I found that the rubber mats for kitchen cabinets with the holes in it to work good in a tool box. You can even glue them in. If you hang your tools then it's a no brainer. -- LSmFT I'm trying to think but nothing happens............
From: Paul on 5 Jul 2010 13:45
Bill Horn wrote: > Sometimes a good idea is only a suggestion away. > > I have your typical set of metric and english combination box/open-end > wrench sets in various drawers in my toolbox. > > But they're all jumbled about such that it takes longer than I'd like to > grab a certain size or a sequence of certain sizes. > > How do you store your combination wrenches so that they are easy to access? I have separate tool boxes since I have sockets, allen wrenches, and other tools in in both English and Metric. |